JHS Pedals The AT+ Andy Timmons Signature Overdrive | Boost / Overdrive / Distortion / Fuzz

Χαρακτηριστικά

JHS Pedals The AT+ Andy Timmons Signature Overdrive | Boost / Overdrive / Distortion / Fuzz

The JHS Pedals AT is Andy Timmons’ signature overdrive pedal that gives Andy his unmistakable lead and rhythm tone. Upon purchasing a JHS Angry Charlie in 2013, Andy began using it as his primary tone and soon after got in touch with Josh Scott about modifying it for his needs. By collaborating to tailor the pedal to Andy’s tastes, the “@“ was born and released in 2016. This pedal gives you all the soaring overdrive and distortion that you hear from Andy with plenty of options to craft your tone with your rig.  So pay ATtention and we’ll see what makes the AT rock.

Does the AT+ Sound the Same as The Original At?

Yes! The Drive Channel of The At+ Is Identical to Our Original at Pedal.  No Changes Were Made Whatsoever and The Controls Remain the Same. They Include Volume, Eq, Drive, Air, and A Three-Way Toggle for 25-Watt, 50-Watt, or 100-Watt Modes. the Volume Gives You Plenty of Headroom to Play With, While the Drive Control Has a Wide Range from High Gain Blues to Thunderous Distortion. the Tone Controls Work Together to Give You the Ability to Shape Your Tone and Sit Perfectly in A Mix. the Eq Works as A Standard Bright/dark Tone Control, While the Air Control Rolls in Top End Like a Presence Control so You Can Have Just the Right Amount of Brightness for Articulation and Clarity. the Three-Way Toggle Gives You the Feel of Different Amplifier Wattages. the Up Position Is the 25-Watt Setting with The Most Compression and Saturation and The Least Amount of Volume. the Down Position Is the 50-Watt Setting for A Good Balance of Compression and Openness. the Middle Position Is the 100-Watt Position for Tons of Volume and Open Crunch While Being Less Focused.

Two Channels Are Better than One!  

New to The At+ Is an Independent Foot-Switchable Boost, Essentially Creating a Second Channel and Gain Stage for The Pedal. the Boost Side of The At+ Is a Slightly Dirty and Overdriven Pre-Boost that Allows You to Hit the Front End of The at Drive Channel and Achieve More Saturation and Definition for Applications Where You Need More. Since the Boost Is Independent, It Can Be Used Alone to Drive Your Amp or Other Drive Pedals in Conjunction with The At+ Drive Channel.

Version History

V1 = Diamond shape knob layout; single foot switch.

V2 = “AT+” U-shaped knob layout; two foot switches; limited edition AT+ pedals also come in a Sweetwater exclusive black enclosure.

This Pedal Requires Standard 9v DC Center Negative Power, Consumes 15ma, and Measures 2.2" X 4.8" X 1.6".

You Can Safely Run the “AT“ at 18 or 9 Volts

• Volume: Controls the output volume.
• Drive: Controls the amount of drive/gain just like a tube amp being cranked at high volumes.
• EQ: High pass filter that naturally brightens or darkens the overall tone of the pedal. Right is brighter, left is darker.
• Air: Just like the presence knob on an amp, this allows you to dial in the perfect amount of high end for compatibility with any amp. Right is brighter, left is darker.
• Boost: Controls the volume of the independent boost circuit. Right is more, left is less.
• Toggle: Gives you 25w/50w/100w feel. Up is 25w, down is 50w, and middle is 100w.
• Input: 1/4” jack on the right side of the pedal.
• Output: 1/4” jack on the left side of the pedal.
• Power: Uses 9V to 18V DC Negative Center. This pedal CAN be run at 18V for more headroom and greater
• dynamics. Do not use more than 18V DC. Your warranty will be voided. 15mA consumption